Full Bore Butterfly Valve
1.Introduction of Full bore butterfly valve
The full bore butterfly valve has an internal flow channel of sufficient size to allow the flow of material to pass through without any obvious restriction, and the internal flow is equal to the full area of the inlet; the Full bore butterfly valve is mainly used for on-off and open circuit conditions, where the logistics must be stopped or dedicated . The Full bore butterfly valve produced by Milestone Valve Company has excellent quality, stable performance and good sealing performance, and is widely used in water supply and drainage, petroleum, chemical, construction, medicine, food and other fields.
2.Technical parameters of Full bore butterfly valve:
|Type of Valve||Full-bore butterfly valve|
|Design Temperature Range||-15℃～150℃|
|Connection type:||Flanged, Wafer ,Butt weld, Lug|
|Actuator type||Manual drive, Pneumatic, Hydraulic or electric Actuator|
|Sealing||Soft seal, Metal Hard Seal|
|Applicable Medium||Water, oil, gas, and various corrosion medium|
Material of main parts
Gray Iron, Ductile Iron, Al-bronze,
Stainless Steel, Carbon steel
|Disc||Ductile iron, Stainless Steel, Al-bronze|
|Shaft||Cast Iron, Stainless Steel|
|Seat||Rubber, stainless steel, stellite|
|Stem||Stainless steel, duplex steel|
|Sealing||O-ring, NBR, EPDM, FKM|
3.Full bore butterfly valve is classified according to the connection method:
1)The flange type Full bore butterfly valve is a vertical plate structure. There are two integrally cast flanges on both sides of the butterfly valve, which are directly connected to the pipeline flange. They are manufactured by the same standard. Such a butterfly valve is also called a double flange. Butterfly valve
2)The wafer type Full bore butterfly valve is installed in the diameter direction of the pipe, and the valve is fully open. The four holes on the valve body are used for positioning, and the processing standards for the four holes are the same as the pipe flange standards. Use two flanges on the pipe to clamp the butterfly plate and fix it with bolts. , Wafer type Full bore butterfly valve has simple structure, small size and light weight, so it is the most widely applicable and most sold connection method.
3)The lug type Full bore butterfly valve is based on the wafer type Full bore butterfly valve, which completes the pressure holes on all flanges. The installation method is similar to the wafer butterfly valve.
4)Butt-welding type Full bore butterfly valve is that both the pipe and the butterfly valve are processed with a groove, and the groove can be completed by electric welding. After cooling, the butterfly valve is completely welded to the pipeline. Such a butterfly valve requires great quality requirements. If an accident occurs, the butterfly valve needs to be disassembled, and the valve needs to be cut off as a whole, and the maintenance cost is very high.
4.Application fields of full bore butterfly valve：
5.Packaging and Delivery
1. Can i have a sample order for valve ?
A: Yes, we welcome sample order to test and check the quality, Mixed sample are accepted.
2. Do you have any MOQ limit for valve order ?
A: Low MOQ, 1 PC for sample checking is avaible.
3. Could you offer OEM service ?
A: Yes, OEM is availble.
4. How about the payment ?
A: We normally accept 30% deposit, and balance will be paid before shipping. L7C is OK
5. Whafs the delivery time of your butterfly valves?
A: For most of the sizes,DN50-DN600,we have stock of valve parts,it*s possible to deliver in 1-3 weeks,to nearest seaport Tianjin.
6. Whafs the warranty of your products?
A:We normally offer 12 months of warranty in service or 18 months since shipping date.
7. What is your products standardization?
A: GB/T12238-2008, JBfT 8527-1997, API 609,EN 593-1998, DIN 85003-3-1997
7. Contact Information